Product category:
Electrical Services
News Release from: IDEC Electronics | Subject: GSM modem
Edited by the Buildingtalk Editorial
Team on 28 March 2006
Connecting GSM modems to PLCs
The advantages of connecting a low cost GSM modem to a programmable controller application are many, alarm messages can be sent to a nominated mobile or fax number.
The advantages of connecting a low cost GSM modem to a programmable controller application are many, alarm messages can be sent to a nominated mobile or fax number diagnostic information can be retrieved upon ringing the GSM modem number or for extra security a coded text message can be sent, which the PLC will check before releasing information
This article was originally published on Buildingtalk on 7 May 2007 at 8.00am (UK)
Related stories
WindO/I-NV2 compatibility with Windows Vista
IDEC Electronics latest version of WindO/I version 3.30 HMI programming software incorporates a number of new features.
Flush silhouette control units from IDEC
IDEC Electronics are now producing a range of control units that present a flush silhouette appearance to the front of a control panel.
Whatever the requirements the operator knows he can be contacted by the PLC when situations arise - ideal for those critical unmanned locations.
Communication to the modem from the PLC is by serial RS232 interface and the protocol used is by AT commands, the standard way of communicating with a modem.
The PLC must be capable of transmitting ASCII codes in order to achieve this.
Further reading
HS5E safety gate switch from IDEC Electronics
This door interlock switch is designed to protect workers in potentially hazardous situations and is a more reliable alternative than a limit switch.
E-stops employ direct opening action
Idec's one of a kind XA (and the larger XW 22mm E-Stop) employ a direct opening action mechanism which meets IEC60947-5-5, 5.2, IEC60947-5-1, Annex K standards.
Two minutes after power up (to allow time for the GSM to register with its network) the PLC will send a ATZ reset to the modem.
This will be resent every 2 minutes until an OK prompt has been received from the modem.
The PLC then sets up the modem for text mode and for incoming SMS reports via the AT+CMGF and AT+CNMI commands.
An alarm situation will be arranged to trigger a transmit message to the modem which is sent in two parts.
The first part is an AT+CMGS command which includes the telephone number of the receiving mobile or, if a prefix code is used a nominated fax number.
The second part is triggered when a < prompt is received from the modem signifying it is ready.
This second message contains the actual SMS text which could also contain live PLC register data.
This could be data signifying for example piece part counts or analog temperature/pressure values etc If the modem's own telephone number is rung from an outside source a RING prompt is sent to the PLC.
If the PLC recognizes this it will respond with an AT+CMGS command as above and send its data.
If security of this information is of concern then an SMS text message can be sent to the modem containing a code or password known only to the user.
These text messages are stored sequentially in the modem in a number of memory locations.
Upon receiving a text message a +CMTI prompt from the modem identifies which memory location the new message is stored in.
The PLC will then respond with a CMGR command which reads and stores the whole message in its data registers.
The PLC checks this data using its standard compare instructions to see if a valid password has been sent and if so, release its information using an AT+CMGS command as described above.
The last thing the PLC is required to do is to clear out the text message stored in the last memory location by send an AT+CMGD command to the modem with its memory location number.
By putting the required programme in the PLC, any action can be triggered by a coded incoming text message.
The PLC and therefore the machine it is controlling could even be turned off if the user has not paid his bill!.
• IDEC Electronics: contact details and other news
• Email this article to a colleague
• Register for the free Buildingtalk email newsletter
• Buildingtalk Home Page
Search the Pro-Talk network of sites
